Serving the Greenville area  ·  (252) 351-2955  ·  Open Mon-Sun 7am-7pm
📞 (252) 351-2955 Free Quote

Metal Roofing in Greenville, NC (27834) · Local Professionals

Greenville Metal Roofing · Fast response in Greenville and the Greenville area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+170Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Greenville's mix of 1920s Craftsman bungalows near the Tar River and 1970s brick ranches out toward Brook Valley means one thing for roofs: heat, humidity, and hurricane-season wind that finds every weak fastener. If your shingles are streaking green or your porch ceiling is staining after a storm, you are not alone on this block.

Homeowners in the 27834 ZIP call Greenville Metal Roofing because we know how standing seam and metal shingle roofs handle Pitt County's sandy loam, pine needles, and summer downpours. We are based here, we work here, and we have seen what a nor'easter does to a low-pitched ranch roof off East 10th Street.

Metal Roofing in Greenville (27834)

Greenville sits on the flat Tar River floodplain, about 50 feet above sea level, with sandy loam soil that drains fast but shifts under old brick piers. In the uptown historic districts near the university, we work on Queen Anne and Colonial Revival homes with deep porches and steep pitches where flashing details around chimneys and dormers matter more than panel count. Out in Brook Valley, Cherry Oaks, and Biltmore, the 1950s to 1970s brick ranches have low-slope shingle roofs that bake in July and leak at the eaves when tropical moisture sits for days. In newer subdivisions like Ironwood and Red Banks, HOA design review often limits panel profile and color, so we bring samples and handle the paperwork before we order metal. Farmhouses and tobacco barns across the coastal plain need corrugated or ribbed panels that shed limbs and debris, and we install those too.

Our team has replaced, repaired, and retrofitted metal roofs across Greenville and the surrounding areas, from Winterville and Ayden to the streets around East Carolina University. We know which suppliers stock the panel profiles that pass local inspections, and we know how to schedule work around Greenville's summer thunderstorms.

Our services in Greenville

How a Job Works in Greenville

Step 1: You call (252) 351-2955 or request a free estimate. We schedule an on-site assessment, walk your roof and attic, check fasteners, seams, and flashing, and give you a written scope with pricing. No pressure, no vague ballparks.

Step 2: Once you approve, we pull the required roofing permit through the local building department and coordinate any historic district or HOA review. On tight lots in the uptown districts, we stage materials in the driveway and use magnetic sweepers daily. For a full replacement, we protect landscaping and set up safely around porches and gutters.

Step 3: We clean the site completely, haul away old shingles and metal scraps, and walk the finished roof with you. We do not leave until you have seen the seams, flashing, and gutter tie-ins yourself.

Pricing in Greenville depends on roof size, pitch, access, and condition. Metal roof installation starts at $8 per square foot, standing seam at $10, metal roof replacement at $9, and a retrofit over existing shingles at $7. Repairs start at $450, screw replacement and re-fastening at $750, and flashing or chimney repair at $600. Coating and painting starts at $2.50 per square foot, and gutters for metal roofs start at $9 per linear foot. Storm damage inspections are free. Call (252) 351-2955 for a free estimate that reflects your actual roof, not a phone guess.

My 1960s brick ranch in Brook Valley has a low-pitch roof that pools water near the eaves. Can metal roofing fix that?
Yes, but the fix is in the details. Low-slope roofs need standing seam panels or a mechanically seamed profile with proper underlayment and eave flashing. We check the decking and slope first, then recommend a panel that sheds water instead of relying on shingle overlap. Many Brook Valley homeowners choose standing seam because it handles the low pitch and summer heat better than architectural shingles.
A storm just dropped a pine limb on my roof near East Carolina University. How fast can you get out?
We prioritize active leaks and storm damage in Greenville. Call (252) 351-2955 and we will schedule an inspection, often same day or next day depending on storm volume. We can tarp a puncture temporarily and give you a written repair estimate for insurance documentation. We never promise coverage, but we document what we find.
What does a typical metal roof replacement cost for a 1,800-square-foot house in the 27834 ZIP code?
Most full replacements in Greenville fall between $9 and $12 per square foot installed, depending on panel type, pitch, and whether we remove existing shingles. A 1,800-square-foot roof might land in the $16,000 to $22,000 range for standing seam, or less for corrugated or ribbed panels. Repairs start at $450. Call (252) 351-2955 for a free estimate on your specific roof.
Do I need a permit to replace my roof in Greenville, and does the historic district change anything?
Roofing permits are commonly required for a full replacement or re-roof, and thresholds and fees vary by jurisdiction. If your home is in a historic district, design review may restrict panel profile and color. We always defer to the local building department for the final word, and you can check the City of Greenville website for contact information. We handle the permit paperwork as part of the job.
My neighbor says my new metal roof edge crosses the property line. What should I do before work starts?
We mark the roofline and gutter tie-ins before installation and flag any overhang that looks close to a property line. If there is a dispute, we recommend a survey or a conversation with your neighbor before panels go up. For HOA communities in Ironwood or Red Banks, we submit the panel profile and color for approval first so there are no surprises after the fact.
Are you insured for roof work on my Greenville property?
Yes. Greenville Metal Roofing is fully insured with general liability and workers' compensation coverage.
What maintenance does a metal roof need in Greenville's humid summers?
Metal roofs here mainly need annual inspections of fasteners, seams, and flashing, plus clearing pine needles and debris from valleys and gutters. Algae and moss are less of an issue on metal than shingles, but our humid summers can still leave organic buildup on north-facing panels. A coating or soft wash every few years keeps the finish intact. We offer free inspections to catch loose fasteners before the next hurricane season.
Why choose us?

Trusted professionals in Greenville

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Greenville

All your work handled by qualified professionals in Greenville

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

170+ Verified Client Reviews in Greenville

⭐⭐⭐⭐⭐ 4.9/5 · 170 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Greenville · Response within 24h · No commitment · ☎ (252) 351-2955

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Greenville ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm